Original file

Mercedes-Benz Sprinter219 319 419 519 Bosch EDC17CP10 CR6NFZ-642-55N5-906M-CHARGE4_LSU-OLA_3ZNW-140KW-EURO5_OP-ME3 / 1037501644

An original (stock) flash read of the Bosch EDC17CP10 control unit, fitted in Mercedes-Benz Sprinter219 319 419 519, hardware number CR6NFZ-642-55N5-906M-CHARGE4_LSU-OLA_3ZNW-140KW-EURO5_OP-ME3 and software number 1037501644, 2,048.00 KB. The file is supplied exactly as it was read from the unit, byte for byte; nothing is changed in it.

Is this your file?

Compare these numbers with the label on your control unit before you order.

Vehicle
Mercedes-Benz Sprinter219 319 419 5193.0 diesel 140KW
Control unit
Bosch EDC17CP10
Read type
Calibration only (data set)
File
2,048.00 KB · Flash
Hardware number
CR6NFZ-642-55N5-906M-CHARGE4_LSU-OLA_3ZNW-140KW-EURO5_OP-ME3
Software number
1037501644
Software / calibration
6429027200

Technical data

Vehicle
BrandMercedes-Benz
Car modelSprinter219 319 419 519
Engine3.0 diesel 140KW
Control unit
Control unitBosch EDC17CP10
ECU makerBosch
Hardware numberCR6NFZ-642-55N5-906M-CHARGE4_LSU-OLA_3ZNW-140KW-EURO5_OP-ME3
Software number1037501644
File
File typeOriginal flash read
File size2,048.00 KB (2,097,152 bytes)
From the file nameMB Sprinter219 319 419 519
File key48d73eec6ff76a82
Identification read from the file
ECU nameEDC17CP10
Read typeCalibration only (data set)
Bosch part / software1037501644Offset in the file: 0x18801A
Software / calibration6429027200Offset in the file: 0x18211A
Data set number6429037700Offset in the file: 0x182125
Bosch project identifier (EPK)46/1/EDC17CP10/1/P695//P_695_55N5__CV090600///Offset in the file: 0x188A10

About this file

Typical uses: restoring a control unit to its factory software after a failed flash or a corrupt memory, a clean base before any change, comparing a read of your own with the original. The checksum is the one of the read; your programmer or the CARTESIAN app corrects it after a change.

In CARTESIAN this original file is the base for DPF off, EGR off, AdBlue (SCR) off, lambda off, swirl flaps off and DTC off, each saved with a correct checksum, and for returning a modified unit to stock.

How to use this file

  1. Order with your e-mail address; the download link comes right after the payment and is valid for 30 days.
  2. Open the file in your programmer, compare its numbers with your unit and check the checksum.
  3. Write it only to a Bosch EDC17CP10 whose label carries the same hardware and software numbers.

Before you write Compare the numbers on your control unit with this file, hardware number CR6NFZ-642-55N5-906M-CHARGE4_LSU-OLA_3ZNW-140KW-EURO5_OP-ME3 and software number 1037501644. A file written to a unit with other numbers can damage it. Not sure? Search with your own read on the Database page: it is compared by content.

Other reads of this pair

The same hardware and software numbers, read from other vehicles or at other times; each has its page.

VehiclesSizePriceAdd to cart
Mercedes-Benz RegentlFlash2,048.00 KB€15Add to cart
Mercedes-Benz SprinterFlash4,096.00 KB€15Add to cart
Mercedes-Benz SprinterFlash4,096.00 KB€15Add to cart
Mercedes-BenzFlash · From the file name: MB Bosch EDC17CP10 140kW EURO54,096.00 KB€15Add to cart
Mercedes-Benz SprinterFlash · From the file name: Mercedes Sprinter EDC17CP10 140kW EURO54,096.00 KB€15Add to cart
Mercedes-Benz Sprinter219/319/419/519Flash4,096.00 KB€15Add to cart
Mercedes-Benz Sprinter 319CDI 2010 TurbodieselFlash · From the file name: MB Sprinter 319CDI 2010 Turbodiesel4,096.00 KB€15Add to cart

All reads of CR6NFZ-642-55N5-906M-CHARGE4_LSU-OLA_3ZNW-140KW-EURO5_OP-ME3 / 1037501644

Other pairs of Bosch EDC17CP10

Bosch EDC17CP10 original files

The Bosch EDC17CP10 unit page