Original file

Mercedes-Benz Sprinter Bosch EDC16CP31 CR6NFZ-642-61N6-906A-CHARGE4_LSUOLA_3ZNW-140KW-NAFTA10_OPS-5 / 1037500231

An original (stock) flash read of the Bosch EDC16CP31 control unit, fitted in Mercedes-Benz Sprinter, hardware number CR6NFZ-642-61N6-906A-CHARGE4_LSUOLA_3ZNW-140KW-NAFTA10_OPS-5 and software number 1037500231, 2,048.00 KB. The file is supplied exactly as it was read from the unit, byte for byte; nothing is changed in it.

Is this your file?

Compare these numbers with the label on your control unit before you order.

Vehicle
Mercedes-Benz Sprinter2.1 diesel 175PS
Control unit
Bosch EDC16CP31
Read type
OBD read (no boot area)
File
2,048.00 KB · Flash
Hardware number
CR6NFZ-642-61N6-906A-CHARGE4_LSUOLA_3ZNW-140KW-NAFTA10_OPS-5
Software number
1037500231
Bosch part / software
1037505834
Software / calibration
6429027000

Technical data

Vehicle
BrandMercedes-Benz
Car modelSprinter
Engine2.1 diesel 175PS
Power175.0PS / 128.7kW
Control unit
Control unitBosch EDC16CP31
ECU makerBosch
Hardware numberCR6NFZ-642-61N6-906A-CHARGE4_LSUOLA_3ZNW-140KW-NAFTA10_OPS-5
Software number1037500231
File
File typeOriginal flash read
File size2,048.00 KB (2,097,152 bytes)
File key564c04455eeb9709
Identification read from the file
ECU nameEDC17CP10
Read typeOBD read (no boot area)
ProcessorTC1796
Bosch part / software1037505834Offset in the file: 0x02001A
Software / calibration6429027000Offset in the file: 0x00FC59
Data set number6429030601Offset in the file: 0x184C11
Bosch project identifier (EPK)45/1/EDC17CP10/1/P695//P_695_61N6_CV094700///Offset in the file: 0x040EE4

About this file

Typical uses: restoring a control unit to its factory software after a failed flash or a corrupt memory, a clean base before any change, comparing a read of your own with the original. The checksum is the one of the read; your programmer or the CARTESIAN app corrects it after a change.

In CARTESIAN this original file is the base for DPF off, EGR off, AdBlue (SCR) off, lambda off, swirl flaps off and DTC off, each saved with a correct checksum, and for returning a modified unit to stock.

How to use this file

  1. Order with your e-mail address; the download link comes right after the payment and is valid for 30 days.
  2. Open the file in your programmer, compare its numbers with your unit and check the checksum.
  3. Write it only to a Bosch EDC16CP31 whose label carries the same hardware and software numbers.

Before you write Compare the numbers on your control unit with this file, hardware number CR6NFZ-642-61N6-906A-CHARGE4_LSUOLA_3ZNW-140KW-NAFTA10_OPS-5 and software number 1037500231. A file written to a unit with other numbers can damage it. Not sure? Search with your own read on the Database page: it is compared by content.

Other reads of this pair

The same hardware and software numbers, read from other vehicles or at other times; each has its page.

VehiclesSizePriceAdd to cart
Mercedes-Benz SprinterFlash2,048.00 KB€15Add to cart

All reads of CR6NFZ-642-61N6-906A-CHARGE4_LSUOLA_3ZNW-140KW-NAFTA10_OPS-5 / 1037500231

Other pairs of Bosch EDC16CP31

HardwareSoftwareVehicles
CR4_NFZ-OM642-PK-S0081037386794Mercedes-Benz Sprinter
CR4_NFZ-OM642-PK-S0131037391219Mercedes-Benz Vito
CR4_NFZ-OM642-PK-S0181037386790Mercedes-Benz Vito
CR6-642-56S0-204SA-165KW-EU4OP_4X4-006C_ME091037392633Mercedes-Benz C
CRA-OM640-PUBKEY-S0071037500676Mercedes-Benz B
ECTCD84YVE4ARHD4A431037384666Chrysler Voyager
EJTCD94YVE6AAE9DA1037396188Chrysler Jeep Wrangler, Chrysler Grand Cherokee
F-1907X063M1037390824Mercedes-Benz CLS

Bosch EDC16CP31 original files

The Bosch EDC16CP31 unit page