Original file

Mercedes-Benz VITO200/220 Bosch EDC17C66 CR41NFZ-651-FFS1-447A_LL-140kW_OVTQ-3OSL2S_D-EU6_OPS-ME04 / 1037550444

An original (stock) flash read of the Bosch EDC17C66 control unit, fitted in Mercedes-Benz VITO200/220, hardware number CR41NFZ-651-FFS1-447A_LL-140kW_OVTQ-3OSL2S_D-EU6_OPS-ME04 and software number 1037550444, 2,048.00 KB. The file is supplied exactly as it was read from the unit, byte for byte; nothing is changed in it.

Is this your file?

Compare these numbers with the label on your control unit before you order.

Vehicle
Mercedes-Benz VITO200/2202.2 diesel 140KW
Control unit
Bosch EDC17C66
Read type
Calibration only (data set)
File
2,048.00 KB · Flash
Hardware number
CR41NFZ-651-FFS1-447A_LL-140kW_OVTQ-3OSL2S_D-EU6_OPS-ME04
Software number
1037550444
Software / calibration
6519029701

Technical data

Vehicle
BrandMercedes-Benz
Car modelVITO200/220
Engine2.2 diesel 140KW
Control unit
Control unitBosch EDC17C66
ECU makerBosch
Hardware numberCR41NFZ-651-FFS1-447A_LL-140kW_OVTQ-3OSL2S_D-EU6_OPS-ME04
Software number1037550444
File
File typeOriginal flash read
File size2,048.00 KB (2,097,152 bytes)
File keyb3da97dd7c099674
Identification read from the file
ECU nameEDC17C66
Read typeCalibration only (data set)
Bosch part / software1037550444Offset in the file: 0x02001A
Software / calibration6519029701Offset in the file: 0x0850DF
Data set number6519033433Offset in the file: 0x0850EA
Boot software6519041400Offset in the file: 0x0850D4
Bosch project identifier (EPK)45/1/EDC17C66/1/P695//P_695_FFS1__CV143400///Offset in the file: 0x020C80

About this file

Typical uses: restoring a control unit to its factory software after a failed flash or a corrupt memory, a clean base before any change, comparing a read of your own with the original. The checksum is the one of the read; your programmer or the CARTESIAN app corrects it after a change.

In CARTESIAN this original file is the base for DPF off, EGR off, AdBlue (SCR) off, lambda off, swirl flaps off and DTC off, each saved with a correct checksum, and for returning a modified unit to stock.

How to use this file

  1. Order with your e-mail address; the download link comes right after the payment and is valid for 30 days.
  2. Open the file in your programmer, compare its numbers with your unit and check the checksum.
  3. Write it only to a Bosch EDC17C66 whose label carries the same hardware and software numbers.

Before you write Compare the numbers on your control unit with this file, hardware number CR41NFZ-651-FFS1-447A_LL-140kW_OVTQ-3OSL2S_D-EU6_OPS-ME04 and software number 1037550444. A file written to a unit with other numbers can damage it. Not sure? Search with your own read on the Database page: it is compared by content.

Other pairs of Bosch EDC17C66

Bosch EDC17C66 original files

The Bosch EDC17C66 unit page