Original file

Mercedes-Benz G280/300 Bosch EDC17CP10 CR6NFZ-642-6DN3-GW461-CHARGE4_LSUOLA_3ZNW-135KW-EURO3_O-006_M / 1037512480

An original (stock) flash read of the Bosch EDC17CP10 control unit, fitted in Mercedes-Benz G280/300, hardware number CR6NFZ-642-6DN3-GW461-CHARGE4_LSUOLA_3ZNW-135KW-EURO3_O-006_M and software number 1037512480, 2,048.00 KB. The file is supplied exactly as it was read from the unit, byte for byte; nothing is changed in it.

Is this your file?

Compare these numbers with the label on your control unit before you order.

Vehicle
Mercedes-Benz G280/3003.0 diesel 184PS
Control unit
Bosch EDC17CP10
Read type
OBD read (no boot area)
File
2,048.00 KB · Flash
Hardware number
CR6NFZ-642-6DN3-GW461-CHARGE4_LSUOLA_3ZNW-135KW-EURO3_O-006_M
Software number
1037512480
Software / calibration
6429023201

Technical data

Vehicle
BrandMercedes-Benz
Car modelG280/300
Engine3.0 diesel 184PS
Power184.0PS / 135.3kW
Control unit
Control unitBosch EDC17CP10
ECU makerBosch
Hardware numberCR6NFZ-642-6DN3-GW461-CHARGE4_LSUOLA_3ZNW-135KW-EURO3_O-006_M
Software number1037512480
File
File typeOriginal flash read
File size2,048.00 KB (2,097,152 bytes)
File key367e5a26f9050251
Identification read from the file
ECU nameEDC17CP10
Read typeOBD read (no boot area)
ProcessorTC1796
Bosch part / software1037512480Offset in the file: 0x02001A
Software / calibration6429023201Offset in the file: 0x03EF03
Data set number6429031407Offset in the file: 0x18613D
Boot software6429040100Offset in the file: 0x00FC59
Bosch project identifier (EPK)45/1/EDC17CP10/1/P695//P_695_6DN3_CV103800///Offset in the file: 0x040EE4

About this file

Typical uses: restoring a control unit to its factory software after a failed flash or a corrupt memory, a clean base before any change, comparing a read of your own with the original. The checksum is the one of the read; your programmer or the CARTESIAN app corrects it after a change.

In CARTESIAN this original file is the base for DPF off, EGR off, AdBlue (SCR) off, lambda off, swirl flaps off and DTC off, each saved with a correct checksum, and for returning a modified unit to stock.

How to use this file

  1. Order with your e-mail address; the download link comes right after the payment and is valid for 30 days.
  2. Open the file in your programmer, compare its numbers with your unit and check the checksum.
  3. Write it only to a Bosch EDC17CP10 whose label carries the same hardware and software numbers.

Before you write Compare the numbers on your control unit with this file, hardware number CR6NFZ-642-6DN3-GW461-CHARGE4_LSUOLA_3ZNW-135KW-EURO3_O-006_M and software number 1037512480. A file written to a unit with other numbers can damage it. Not sure? Search with your own read on the Database page: it is compared by content.

Other pairs of Bosch EDC17CP10

Bosch EDC17CP10 original files

The Bosch EDC17CP10 unit page