Original file

Mercedes-Benz GLK Bosch EDC17CP46 CR42-651-CGWE-X204WA4X-150KW-CH4N-EU6OPS-LL-EF_NOXTT3-006_M / 10SW086334

An original (stock) flash read of the Bosch EDC17CP46 control unit, fitted in Mercedes-Benz GLK, hardware number CR42-651-CGWE-X204WA4X-150KW-CH4N-EU6OPS-LL-EF_NOXTT3-006_M and software number 10SW086334, 2,048.00 KB. The file is supplied exactly as it was read from the unit, byte for byte; nothing is changed in it.

Is this your file?

Compare these numbers with the label on your control unit before you order.

Vehicle
Mercedes-Benz GLKdiesel 204PS
Control unit
Bosch EDC17CP46
Read type
Calibration only (data set)
File
2,048.00 KB · Flash
Hardware number
CR42-651-CGWE-X204WA4X-150KW-CH4N-EU6OPS-LL-EF_NOXTT3-006_M
Software number
10SW086334
Software / calibration
6519029203

Technical data

Vehicle
BrandMercedes-Benz
Car modelGLK
Enginediesel 204PS
Displacement2.1
Power204.0PS / 150.0kW
Control unit
Control unitBosch EDC17CP46
ECU makerBosch
Hardware numberCR42-651-CGWE-X204WA4X-150KW-CH4N-EU6OPS-LL-EF_NOXTT3-006_M
Software number10SW086334
File
File typeOriginal flash read
File size2,048.00 KB (2,097,152 bytes)
File key8ab06241179d896f
Identification read from the file
ECU nameEDC17CP46
Read typeCalibration only (data set)
Bosch part / software10SW086334Offset in the file: 0x00001A
Software / calibration6519029203Offset in the file: 0x066FBD
Data set number6519035879Offset in the file: 0x066FC8
Boot software6519040101Offset in the file: 0x066FB2
Bosch project identifier (EPK)46/1/EDC17CP46/1/P695//P_695_CGWE__CV195000///Offset in the file: 0x001080

About this file

Typical uses: restoring a control unit to its factory software after a failed flash or a corrupt memory, a clean base before any change, comparing a read of your own with the original. The checksum is the one of the read; your programmer or the CARTESIAN app corrects it after a change.

In CARTESIAN this original file is the base for DPF off, EGR off, AdBlue (SCR) off, lambda off, swirl flaps off and DTC off, each saved with a correct checksum, and for returning a modified unit to stock.

How to use this file

  1. Order with your e-mail address; the download link comes right after the payment and is valid for 30 days.
  2. Open the file in your programmer, compare its numbers with your unit and check the checksum.
  3. Write it only to a Bosch EDC17CP46 whose label carries the same hardware and software numbers.

Before you write Compare the numbers on your control unit with this file, hardware number CR42-651-CGWE-X204WA4X-150KW-CH4N-EU6OPS-LL-EF_NOXTT3-006_M and software number 10SW086334. A file written to a unit with other numbers can damage it. Not sure? Search with your own read on the Database page: it is compared by content.

Other pairs of Bosch EDC17CP46

Bosch EDC17CP46 original files

The Bosch EDC17CP46 unit page