Original file

Mercedes-Benz ML350 Bosch EDC17CP46 CR60-BJLQ-166WA-642LS-EU6_1OPS_4X4_3S_MY15_2_NOXTT3-ME33 / 10SW065544

An original (stock) flash read of the Bosch EDC17CP46 control unit, fitted in Mercedes-Benz ML350, hardware number CR60-BJLQ-166WA-642LS-EU6_1OPS_4X4_3S_MY15_2_NOXTT3-ME33 and software number 10SW065544, 4,096.00 KB. The file is supplied exactly as it was read from the unit, byte for byte; nothing is changed in it.

Is this your file?

Compare these numbers with the label on your control unit before you order.

Vehicle
Mercedes-Benz ML3503.0 diesel 258PS
Control unit
Bosch EDC17CP46
Read type
Calibration only (data set)
File
4,096.00 KB · Flash
Hardware number
CR60-BJLQ-166WA-642LS-EU6_1OPS_4X4_3S_MY15_2_NOXTT3-ME33
Software number
10SW065544
Software / calibration
6429028703

Technical data

Vehicle
BrandMercedes-Benz
Car modelML350
Engine3.0 diesel 258PS
Power258.0PS / 189.8kW
Control unit
Control unitBosch EDC17CP46
ECU makerBosch
Hardware numberCR60-BJLQ-166WA-642LS-EU6_1OPS_4X4_3S_MY15_2_NOXTT3-ME33
Software number10SW065544
File
File typeOriginal flash read
File size4,096.00 KB (4,194,304 bytes)
File key8e6af9e90a452c63
Identification read from the file
ECU nameEDC17CP46
Read typeCalibration only (data set)
Bosch part / software10SW065544Offset in the file: 0x34001A
Software / calibration6429028703Offset in the file: 0x3A2C6F
Data set number6429032816Offset in the file: 0x3A2C7A
Boot software6429040200Offset in the file: 0x3A2C64
Bosch project identifier (EPK)46/1/EDC17CP46/1/P695//P_695_BJLQ__CV195000///Offset in the file: 0x341080

About this file

Typical uses: restoring a control unit to its factory software after a failed flash or a corrupt memory, a clean base before any change, comparing a read of your own with the original. The checksum is the one of the read; your programmer or the CARTESIAN app corrects it after a change.

In CARTESIAN this original file is the base for DPF off, EGR off, AdBlue (SCR) off, lambda off, swirl flaps off and DTC off, each saved with a correct checksum, and for returning a modified unit to stock.

How to use this file

  1. Order with your e-mail address; the download link comes right after the payment and is valid for 30 days.
  2. Open the file in your programmer, compare its numbers with your unit and check the checksum.
  3. Write it only to a Bosch EDC17CP46 whose label carries the same hardware and software numbers.

Before you write Compare the numbers on your control unit with this file, hardware number CR60-BJLQ-166WA-642LS-EU6_1OPS_4X4_3S_MY15_2_NOXTT3-ME33 and software number 10SW065544. A file written to a unit with other numbers can damage it. Not sure? Search with your own read on the Database page: it is compared by content.

Other pairs of Bosch EDC17CP46

Bosch EDC17CP46 original files

The Bosch EDC17CP46 unit page