Original file
Mercedes-Benz Sprinter Bosch EDC17CP46 CR60NFZ-642-CDL0-906A_NAG1-140kW-NAFTA13_MY13_OPS-3 / 1037516354
An original (stock) flash read of the Bosch EDC17CP46 control unit, fitted in Mercedes-Benz Sprinter, hardware number CR60NFZ-642-CDL0-906A_NAG1-140kW-NAFTA13_MY13_OPS-3 and software number 1037516354, 4,096.00 KB. The file is supplied exactly as it was read from the unit, byte for byte; nothing is changed in it.
Is this your file?
Compare these numbers with the label on your control unit before you order.
- Vehicle
- Mercedes-Benz Sprinter190PS
- Control unit
- Bosch EDC17CP46
- Read type
- Full read (boot area included)
- File
- 4,096.00 KB · Flash
- Hardware number
- CR60NFZ-642-CDL0-906A_NAG1-140kW-NAFTA13_MY13_OPS-3
- Software number
- 1037516354
- Bosch part / software
- 1037535686
- Software / calibration
- 6429029401
Technical data
| Brand | Mercedes-Benz |
|---|---|
| Car model | Sprinter |
| Engine | 190PS |
| Power | 190.3PS / 140.0kW |
| Control unit | Bosch EDC17CP46 |
|---|---|
| ECU maker | Bosch |
| Hardware number | CR60NFZ-642-CDL0-906A_NAG1-140kW-NAFTA13_MY13_OPS-3 |
| Software number | 1037516354 |
| File type | Original flash read |
|---|---|
| File size | 4,096.00 KB (4,194,304 bytes) |
| File key | 9f4a5802ef235ffe |
| ECU name | EDC17CP46 | |
|---|---|---|
| Read type | Full read (boot area included) | |
| Processor | TC1797 | |
| Bosch part / software | 1037535686 | Offset in the file: 0x02001A |
| Software / calibration | 6429029401 | Offset in the file: 0x02022F |
| Data set number | 6429034806 | Offset in the file: 0x2061FC |
| Boot software | 6429040300 | Offset in the file: 0x00FC51 |
| Bosch project identifier (EPK) | 46/1/EDC17CP46/1/P695//P_695_CDL0__CV125000/// | Offset in the file: 0x057D90 |
About this file
Typical uses: restoring a control unit to its factory software after a failed flash or a corrupt memory, a clean base before any change, comparing a read of your own with the original. The checksum is the one of the read; your programmer or the CARTESIAN app corrects it after a change.
In CARTESIAN this original file is the base for the solutions it supports, such as DPF off, EGR off, lambda off and DTC off, each saved with a correct checksum, and for returning a modified unit to stock.
How to use this file
- Order with your e-mail address; the download link comes right after the payment and is valid for 30 days.
- Open the file in your programmer, compare its numbers with your unit and check the checksum.
- Write it only to a Bosch EDC17CP46 whose label carries the same hardware and software numbers.
Before you write Compare the numbers on your control unit with this file, hardware number CR60NFZ-642-CDL0-906A_NAG1-140kW-NAFTA13_MY13_OPS-3 and software number 1037516354. A file written to a unit with other numbers can damage it. Not sure? Search with your own read on the Database page: it is compared by content.
Other pairs of Bosch EDC17CP46
| Hardware | Software | Vehicles |
|---|---|---|
| CR60-BUL2-166XA-642LS-BIN5OPS_NOXTT3_4X4_CUKAT_MY15-ME40 | 10SW071755 | Mercedes-Benz GL350 |
| CR60-BUL2-166XA-642LS-BIN5OPS_NOxTT3_4x4_CuKat_MY15-ME40 | 6429023704 | Mercedes-Benz GL350 |
| CR60-BUL2-CH4_Q2-166WA-BIN5OPS_NOXTT3_4X4_CUKAT-ME42 | 10SW088882 | Mercedes-Benz ML |
| CR60NFZ-642-CCL0-906A_NAG1-140kW-NAFTA13_OPS-5.0T-ME02 | 1037516354 | Mercedes-Benz Sprinter |
| CR60NFZ-642-CDL0-906A_NAG1-140kW-NAFTA13_MY14_OPS-3 | 1037516354 | Mercedes-Benz Sprinter |
| CR60NFZ-642-CGL0-906A_NAG1_4x2-140kW-CUSCR-NAFTA_MY16_OPS-3 | 1037555771 | Mercedes-Benz Sprinter |
| CR60NFZ-642-CGL1-906A_NAG1_4x2-140kW-CUSCR-NAFTA_MY16_OPS-3 | 1037516354 | Mercedes-Benz Sprinter216/316/416/516 |
| CR60NFZ-642-CGL1-906A_NAG1_4x2-140kW-CUSCR-NAFTA_MY16_OPS-3 | 10SW010725 | Mercedes-Benz Sprinter |