Original file
Mercedes-Benz Sprinter Bosch EDC17CP57 CR61NFZ-642-47A1-907A-140 / 10SW043555
An original (stock) flash read of the Bosch EDC17CP57 control unit, fitted in Mercedes-Benz Sprinter, hardware number CR61NFZ-642-47A1-907A-140 and software number 10SW043555, 4,096.00 KB. The file is supplied exactly as it was read from the unit, byte for byte; nothing is changed in it.
Is this your file?
Compare these numbers with the label on your control unit before you order.
- Vehicle
- Mercedes-Benz Sprinter3.0 190PS
- Control unit
- Bosch EDC17CP57
- Read type
- Calibration only (data set)
- File
- 4,096.00 KB · Flash
- Hardware number
- CR61NFZ-642-47A1-907A-140
- Software number
- 10SW043555
- Software / calibration
- 6429022003
Technical data
| Brand | Mercedes-Benz |
|---|---|
| Car model | Sprinter |
| Engine | 3.0 190PS |
| Fuel | Diesel |
| Control unit | Bosch EDC17CP57 |
|---|---|
| ECU maker | Bosch |
| Hardware number | CR61NFZ-642-47A1-907A-140 |
| Software number | 10SW043555 |
| File type | Original flash read |
|---|---|
| File size | 4,096.00 KB (4,194,304 bytes) |
| File key | 5cdb14bf4e13ae19 |
| ECU name | EDC17CP57 | |
|---|---|---|
| Read type | Calibration only (data set) | |
| Bosch part / software | 10SW043555 | Offset in the file: 0x22001A |
| Software / calibration | 6429022003 | Offset in the file: 0x283B3B |
| Data set number | 6429030713 | Offset in the file: 0x283B46 |
| Boot software | 6429040500 | Offset in the file: 0x283B30 |
| Bosch project identifier (EPK) | 48/1/EDC17CP57/1/P1643//P_1643_47A1__CV182000/// | Offset in the file: 0x221538 |
About this file
Typical uses: restoring a control unit to its factory software after a failed flash or a corrupt memory, a clean base before any change, comparing a read of your own with the original. The checksum is the one of the read; your programmer or the CARTESIAN app corrects it after a change.
In CARTESIAN this original file is the base for DPF off, EGR off, AdBlue (SCR) off, lambda off, swirl flaps off and DTC off, each saved with a correct checksum, and for returning a modified unit to stock.
How to use this file
- Order with your e-mail address; the download link comes right after the payment and is valid for 30 days.
- Open the file in your programmer, compare its numbers with your unit and check the checksum.
- Write it only to a Bosch EDC17CP57 whose label carries the same hardware and software numbers.
Before you write Compare the numbers on your control unit with this file, hardware number CR61NFZ-642-47A1-907A-140 and software number 10SW043555. A file written to a unit with other numbers can damage it. Not sure? Search with your own read on the Database page: it is compared by content.
Other pairs of Bosch EDC17CP57
| Hardware | Software | Vehicles |
|---|---|---|
| CR61-KKH0-253CXA-642LS-EU6OPS_4x4_3S_Eco2-ME09 | W069065P695 | Mercedes-Benz GLC350d |
| CR61NFZ-642-44A0-907A-140 | 10SW034946 | Mercedes-Benz Sprinter |
| CR61NFZ-642-47A1-907A-140 | 017688 | Mercedes-Benz Sprinter |
| CR61NFZ-642-47A1-907A-140 | 10SW017688 | Mercedes-Benz Sprinter |
| CR61NFZ-642-47A1-907A-140 | 10SW043555164347A1 | Mercedes-Benz Sprinter |
| CR61NFZ-642-47A1-907M-140 | 017688 | Mercedes-Benz Sprinter |
| CR61_470-52Q0-VS40-OM642LS-EU5III-ME1 | 10SW017475 | Mercedes-Benz X |
| CR61_470-52Q0-VS40-OM642LS-EU6 | 017475 | Mercedes-Benz X-classe |