Original file

Audi R8 Plus Bosch MED17.1.1 4T0907552A / 10SW018630

An original (stock) flash read of the Bosch MED17.1.1 control unit, fitted in Audi R8 Plus, hardware number 4T0907552A and software number 10SW018630, 4,096.00 KB. The file is supplied exactly as it was read from the unit, byte for byte; nothing is changed in it.

Is this your file?

Compare these numbers with the label on your control unit before you order.

Vehicle
Audi R8 Plus5.2 petrol 610PS
Control unit
Bosch MED17.1.1
Read type
OBD read (no boot area)
File
4,096.00 KB · Flash
Hardware number
4T0907552A
Software number
10SW018630
Software / calibration
4S0907552J

Technical data

Vehicle
BrandAudi
Car modelR8 Plus
Engine5.2 petrol 610PS
Power610.0PS / 448.7kW
Control unit
Control unitBosch MED17.1.1
ECU makerBosch
Hardware number4T0907552A
Software number10SW018630
File
File typeOriginal flash read
File size4,096.00 KB (4,194,304 bytes)
File key6bd9a543aee88939
Identification read from the file
ECU nameMED17.1.1
Read typeOBD read (no boot area)
ProcessorTC1797
Bosch part / software10SW018630Offset in the file: 0x02001A
Vehicle maker's hardware number4T0907552AOffset in the file: 0x3CADA6
Software / calibration4S0907552J · version 0003Offset in the file: 0x3CADC0
Internal build stringMED17 CB.06.02.01Offset in the file: 0x00E8A6
Bosch project identifier (EPK)37/1/MED17/5///D1711A11A000_MY17A5///Offset in the file: 0x13FF08

About this file

Typical uses: restoring a control unit to its factory software after a failed flash or a corrupt memory, a clean base before any change, comparing a read of your own with the original. The checksum is the one of the read; your programmer or the CARTESIAN app corrects it after a change.

In CARTESIAN this original file is the base for lambda off, EGR off, flaps off, start/stop off and DTC off, each saved with a correct checksum, and for returning a modified unit to stock.

How to use this file

  1. Order with your e-mail address; the download link comes right after the payment and is valid for 30 days.
  2. Open the file in your programmer, compare its numbers with your unit and check the checksum.
  3. Write it only to a Bosch MED17.1.1 whose label carries the same hardware and software numbers.

Before you write Compare the numbers on your control unit with this file, hardware number 4T0907552A and software number 10SW018630. A file written to a unit with other numbers can damage it. Not sure? Search with your own read on the Database page: it is compared by content.

Other pairs of Bosch MED17.1.1

HardwareSoftwareVehicles
4T0907552A10SW010988Lamborghini Huracan, Lamborghini Huracán
4T0907552A10SW018626Audi R8
4T0907552A10SW018628Audi R8
4T0907552A10SW018629Audi R8
4T0907552A10SW023147Lamborghini Huracan Performante
4T0907552A10SW023450Lamborghini Huracan
4T0907552A10SW023451Lamborghini Huracan
4T0907552A10SW025028Audi R8 plus

Bosch MED17.1.1 original files

The Bosch MED17.1.1 unit page