Original file

Audi RS4 Bosch MED17.1.1 8T2907560E / 8T2907560E

An original (stock) flash read of the Bosch MED17.1.1 control unit, fitted in Audi RS4, hardware number 8T2907560E and software number 8T2907560E, 2,048.00 KB. The file is supplied exactly as it was read from the unit, byte for byte; nothing is changed in it.

Is this your file?

Compare these numbers with the label on your control unit before you order.

Vehicle
Audi RS44.2 450PS
Control unit
Bosch MED17.1.1
Read type
Calibration only (data set)
File
2,048.00 KB · Flash
Hardware number
8T2907560E
Software number
8T2907560E
Bosch part / software
10SW004335
Vehicle maker's hardware number
8T1907560

Technical data

Vehicle
BrandAudi
Car modelRS4
Engine4.2 450PS
FuelPetrol
Control unit
Control unitBosch MED17.1.1
ECU makerBosch
Hardware number8T2907560E
Software number8T2907560E
File
File typeOriginal flash read
File size2,048.00 KB (2,097,152 bytes)
File key4d023391da1b3ea3
Identification read from the file
ECU nameMED17.1.1
Read typeCalibration only (data set)
Bosch part / software10SW004335Offset in the file: 0x04001A
Vehicle maker's hardware number8T1907560Offset in the file: 0x070FDE
Software / calibration8T2907560E · version 0005Offset in the file: 0x070FF8
Bosch project identifier (EPK)47/1/MED17/5/MED17.1.1//D171156L_MY14B5/Dst00//Offset in the file: 0x07FE08

About this file

Typical uses: restoring a control unit to its factory software after a failed flash or a corrupt memory, a clean base before any change, comparing a read of your own with the original. The checksum is the one of the read; your programmer or the CARTESIAN app corrects it after a change.

In CARTESIAN this original file is the base for lambda off, EGR off, flaps off, start/stop off and DTC off, each saved with a correct checksum, and for returning a modified unit to stock.

How to use this file

  1. Order with your e-mail address; the download link comes right after the payment and is valid for 30 days.
  2. Open the file in your programmer, compare its numbers with your unit and check the checksum.
  3. Write it only to a Bosch MED17.1.1 whose label carries the same hardware and software numbers.

Before you write Compare the numbers on your control unit with this file, hardware number 8T2907560E and software number 8T2907560E. A file written to a unit with other numbers can damage it. Not sure? Search with your own read on the Database page: it is compared by content.

Other pairs of Bosch MED17.1.1

HardwareSoftwareVehicles
8T2907560E1037523849Audi RS4
8T2907560E1037534274Audi RS4, Audi RS5, Audi RS4 4.2 V8 FSI
8T2907560E10SW001141Audi pcmflash, Audi RS5
8T2907560E10SW004335Audi pcmflash, Audi RS4
8T2907560F1037534273Audi RS5, Audi pcmflash
8T2907560F10SW001142Audi pcmflash, Audi RS5
8T2907560F10SW004336Audi RS5, Audi pcmflash
8U0907404B10SW003874Audi pcmflash

Bosch MED17.1.1 original files

The Bosch MED17.1.1 unit page