Original file
BMW F20/F21 Bosch MEVD17.2.5 #C1#DST#MEVD17.2.5-N13-Mo-B16-U0-F020-EU5-HGAG_-LL-RL-PKR / 10SW001131
An original (stock) flash read of the Bosch MEVD17.2.5 control unit, fitted in BMW F20/F21, hardware number #C1#DST#MEVD17.2.5-N13-Mo-B16-U0-F020-EU5-HGAG_-LL-RL-PKR and software number 10SW001131, 2,048.00 KB. The file is supplied exactly as it was read from the unit, byte for byte; nothing is changed in it.
Is this your file?
Compare these numbers with the label on your control unit before you order.
- Vehicle
- BMW F20/F211.6 petrol 136PS
- Control unit
- Bosch MEVD17.2.5
- Read type
- Calibration only (data set)
- File
- 2,048.00 KB · Flash
- Hardware number
- #C1#DST#MEVD17.2.5-N13-Mo-B16-U0-F020-EU5-HGAG_-LL-RL-PKR
- Software number
- 10SW001131
- Software / calibration
- 9ZX99T0B / 0000191E_059_010_006
Technical data
| Brand | BMW |
|---|---|
| Car model | F20/F21 |
| Engine | 1.6 petrol 136PS |
| Power | 136.0PS / 100.0kW |
| Control unit | Bosch MEVD17.2.5 |
|---|---|
| ECU maker | Bosch |
| Hardware number | #C1#DST#MEVD17.2.5-N13-Mo-B16-U0-F020-EU5-HGAG_-LL-RL-PKR |
| Software number | 10SW001131 |
| File type | Original flash read |
|---|---|
| File size | 2,048.00 KB (2,097,152 bytes) |
| File key | 32cfd6c2036bd791 |
| ECU name | MEVD17.2.5 | |
|---|---|---|
| Read type | Calibration only (data set) | |
| Bosch part / software | 10SW001131 | Offset in the file: 0x18001A |
| Software / calibration | 9ZX99T0B / 0000191E_059_010_006 | Offset in the file: 0x1FFE01 |
| Data set description | MEVD17.2.5-N13-Mo-B16-U0-F020-EU5-HGAG_-LL-RL-PKR | |
| Bosch project identifier (EPK) | 40/1/MED17/11/MEVD172X//9ZX99T0B/Dst00// | Offset in the file: 0x1FFB0C |
About this file
Typical uses: restoring a control unit to its factory software after a failed flash or a corrupt memory, a clean base before any change, comparing a read of your own with the original. The checksum is the one of the read; your programmer or the CARTESIAN app corrects it after a change.
In CARTESIAN this original file is the base for lambda off, EGR off, flaps off, start/stop off and DTC off, each saved with a correct checksum, and for returning a modified unit to stock.
How to use this file
- Order with your e-mail address; the download link comes right after the payment and is valid for 30 days.
- Open the file in your programmer, compare its numbers with your unit and check the checksum.
- Write it only to a Bosch MEVD17.2.5 whose label carries the same hardware and software numbers.
Before you write Compare the numbers on your control unit with this file, hardware number #C1#DST#MEVD17.2.5-N13-Mo-B16-U0-F020-EU5-HGAG_-LL-RL-PKR and software number 10SW001131. A file written to a unit with other numbers can damage it. Not sure? Search with your own read on the Database page: it is compared by content.