Original file
BMW 1er Bosch MEVD17.2.6 O_CL2 / 75P9EL0B#9ELHCDX1
An original (stock) flash read of the Bosch MEVD17.2.6 control unit, fitted in BMW 1er, hardware number O_CL2 and software number 75P9EL0B#9ELHCDX1, 4,096.00 KB. The file is supplied exactly as it was read from the unit, byte for byte; nothing is changed in it.
Is this your file?
Compare these numbers with the label on your control unit before you order.
- Vehicle
- BMW 1erN55B30 · 320.0PS / 235.4kW
- Control unit
- Bosch MEVD17.2.6
- Read type
- Full read (boot area included)
- File
- 4,096.00 KB · Flash
- Hardware number
- O_CL2
- Software number
- 75P9EL0B#9ELHCDX1
- Bosch part / software
- 10SW016887
- Software / calibration
- 75P9EL0B / 9ELHCDX1
Technical data
| Brand | BMW |
|---|---|
| Car model | 1er |
| Engine | N55B30 |
| Fuel | Petrol |
| Displacement | 3.0 |
| Power | 320.0PS / 235.4kW |
| Control unit | Bosch MEVD17.2.6 |
|---|---|
| ECU maker | Bosch |
| Hardware number | O_CL2 |
| Software number | 75P9EL0B#9ELHCDX1 |
| File type | Original flash read |
|---|---|
| File size | 4,096.00 KB (4,194,304 bytes) |
| File key | 3b048998edfab05c |
| ECU name | MEVD17.2.6 | |
|---|---|---|
| Read type | Full read (boot area included) | |
| Bosch part / software | 10SW016887 | Offset in the file: 0x18001A |
| Software / calibration | 75P9EL0B / 9ELHCDX1 | Offset in the file: 0x1FFE01 |
| Data set description | MEVD17.2.6-N55-O0-B30-F020-EU5-MSA2-HG_AG-LL-RL-Allrad-PVL-BHDP-M | |
| Bosch project identifier (EPK) | 43/1/MEVD/11/MEVD1726_75P9EL0B//75P9EL0B/// | Offset in the file: 0x1FFB0C |
About this file
Typical uses: restoring a control unit to its factory software after a failed flash or a corrupt memory, a clean base before any change, comparing a read of your own with the original. The checksum is the one of the read; your programmer or the CARTESIAN app corrects it after a change.
In CARTESIAN this original file is the base for lambda off, EGR off, flaps off, start/stop off and DTC off, each saved with a correct checksum, and for returning a modified unit to stock.
How to use this file
- Order with your e-mail address; the download link comes right after the payment and is valid for 30 days.
- Open the file in your programmer, compare its numbers with your unit and check the checksum.
- Write it only to a Bosch MEVD17.2.6 whose label carries the same hardware and software numbers.
Before you write Compare the numbers on your control unit with this file, hardware number O_CL2 and software number 75P9EL0B#9ELHCDX1. A file written to a unit with other numbers can damage it. Not sure? Search with your own read on the Database page: it is compared by content.