Original file
BMW 5er Bosch MEVD17.2.9 #C1#DST#MEVD17.2.P-N20-Mo-B20-U0-F010-EU6-HGAG_-LL-RL / 10SW001851
An original (stock) flash read of the Bosch MEVD17.2.9 control unit, fitted in BMW 5er, hardware number #C1#DST#MEVD17.2.P-N20-Mo-B20-U0-F010-EU6-HGAG_-LL-RL and software number 10SW001851, 2,048.00 KB. The file is supplied exactly as it was read from the unit, byte for byte; nothing is changed in it.
Is this your file?
Compare these numbers with the label on your control unit before you order.
- Vehicle
- BMW 5er2.0 diesel 184PS
- Control unit
- Bosch MEVD17.2.9
- Read type
- Calibration only (data set)
- File
- 2,048.00 KB · Flash
- Hardware number
- #C1#DST#MEVD17.2.P-N20-Mo-B20-U0-F010-EU6-HGAG_-LL-RL
- Software number
- 10SW001851
- Software / calibration
- 9VT9G20B / 9G2LBDX6
Technical data
| Brand | BMW |
|---|---|
| Car model | 5er |
| Engine | 2.0 diesel 184PS |
| Fuel | Petrol |
| Power | 184.0PS / 135.3kW |
| Control unit | Bosch MEVD17.2.9 |
|---|---|
| ECU maker | Bosch |
| Hardware number | #C1#DST#MEVD17.2.P-N20-Mo-B20-U0-F010-EU6-HGAG_-LL-RL |
| Software number | 10SW001851 |
| File type | Original flash read |
|---|---|
| File size | 2,048.00 KB (2,097,152 bytes) |
| File key | e9f0abf64c129adf |
| ECU name | MEVD17.2.9 | |
|---|---|---|
| Read type | Calibration only (data set) | |
| Bosch part / software | 10SW001851 | Offset in the file: 0x18001A |
| Software / calibration | 9VT9G20B / 9G2LBDX6 | Offset in the file: 0x1FFE01 |
| Data set description | MEVD17.2.P-N20-Mo-B20-U0-F010-EU6-HGAG_-LL-RL | |
| Bosch project identifier (EPK) | 43/1/MEVD/11/MEVD1729_9VT9G20B//9VT9G20B/// | Offset in the file: 0x1FFB0C |
About this file
Typical uses: restoring a control unit to its factory software after a failed flash or a corrupt memory, a clean base before any change, comparing a read of your own with the original. The checksum is the one of the read; your programmer or the CARTESIAN app corrects it after a change.
In CARTESIAN this original file is the base for lambda off, EGR off, flaps off, start/stop off and DTC off, each saved with a correct checksum, and for returning a modified unit to stock.
How to use this file
- Order with your e-mail address; the download link comes right after the payment and is valid for 30 days.
- Open the file in your programmer, compare its numbers with your unit and check the checksum.
- Write it only to a Bosch MEVD17.2.9 whose label carries the same hardware and software numbers.
Before you write Compare the numbers on your control unit with this file, hardware number #C1#DST#MEVD17.2.P-N20-Mo-B20-U0-F010-EU6-HGAG_-LL-RL and software number 10SW001851. A file written to a unit with other numbers can damage it. Not sure? Search with your own read on the Database page: it is compared by content.