Original file

Alpina B4 3.0 BiTurbo Bosch MEVD17.2.G 000037B0_019_030_010 000037B0131E0A / #75Y9G07B#000037B0-F32

An original (stock) flash read of the Bosch MEVD17.2.G control unit, fitted in Alpina B4 3.0 BiTurbo, hardware number 000037B0_019_030_010 000037B0131E0A and software number #75Y9G07B#000037B0-F32, 4,096.00 KB. The file is supplied exactly as it was read from the unit, byte for byte; nothing is changed in it.

Is this your file?

Compare these numbers with the label on your control unit before you order.

Vehicle
Alpina B4 3.0 BiTurbo3.0 petrol 410.0PS / 301.6kW
Control unit
Bosch MEVD17.2.G
Read type
Full read (boot area included)
File
4,096.00 KB · Flash
Hardware number
000037B0_019_030_010 000037B0131E0A
Software number
#75Y9G07B#000037B0-F32
Bosch part / software
10SW000193
Software / calibration
75Y9G07B

Technical data

Vehicle
BrandAlpina
Car modelB4 3.0 BiTurbo
Engine3.0 petrol 410.0PS / 301.6kW
Control unit
Control unitBosch MEVD17.2.G
ECU makerBosch
Hardware number000037B0_019_030_010 000037B0131E0A
Software number#75Y9G07B#000037B0-F32
File
File typeOriginal flash read
File size4,096.00 KB (4,194,304 bytes)
File key38388073db0bf5a9
Identification read from the file
ECU nameMEVD17.2.G
Read typeFull read (boot area included)
ProcessorTC1797
Bosch part / software10SW000193Offset in the file: 0x18001A
Software / calibration75Y9G07BOffset in the file: 0x1FFE01
Data set descriptionMEVD17.2.G-N55-ML-R30-ECE-EU6-MSA2-AG__AG-LL-4WD-2xHDP5-ALP-AUG16-8684326
Internal build stringMEVD17.2.G-CB_L6C-D6.2.0_G.5.18.0Offset in the file: 0x00FDBC
Bosch project identifier (EPK)43/1/MEVD/11/MEVD172G_75Y9G07B//75Y9G07B///Offset in the file: 0x17FB0C

About this file

Typical uses: restoring a control unit to its factory software after a failed flash or a corrupt memory, a clean base before any change, comparing a read of your own with the original. The checksum is the one of the read; your programmer or the CARTESIAN app corrects it after a change.

In CARTESIAN this original file is the base for lambda off, EGR off, flaps off, start/stop off and DTC off, each saved with a correct checksum, and for returning a modified unit to stock.

How to use this file

  1. Order with your e-mail address; the download link comes right after the payment and is valid for 30 days.
  2. Open the file in your programmer, compare its numbers with your unit and check the checksum.
  3. Write it only to a Bosch MEVD17.2.G whose label carries the same hardware and software numbers.

Before you write Compare the numbers on your control unit with this file, hardware number 000037B0_019_030_010 000037B0131E0A and software number #75Y9G07B#000037B0-F32. A file written to a unit with other numbers can damage it. Not sure? Search with your own read on the Database page: it is compared by content.

Other pairs of Bosch MEVD17.2.G

Bosch MEVD17.2.G original files

The Bosch MEVD17.2.G unit page