Original file

BMW 4er Bosch MEVD17.2.G DST#MEVD17.2.G-N55-M0-B30-F030-EU6-MSA2-HG_AG-LL-RL-CVO-BHDP / 75Q9H10B#9H1JMAX2

An original (stock) flash read of the Bosch MEVD17.2.G control unit, fitted in BMW 4er, hardware number DST#MEVD17.2.G-N55-M0-B30-F030-EU6-MSA2-HG_AG-LL-RL-CVO-BHDP and software number 75Q9H10B#9H1JMAX2, 2,048.00 KB. The file is supplied exactly as it was read from the unit, byte for byte; nothing is changed in it.

Is this your file?

Compare these numbers with the label on your control unit before you order.

Vehicle
BMW 4erN55B30 · 306.0PS / 225.1kW
Control unit
Bosch MEVD17.2.G
Read type
Calibration only (data set)
File
2,048.00 KB · Flash
Hardware number
DST#MEVD17.2.G-N55-M0-B30-F030-EU6-MSA2-HG_AG-LL-RL-CVO-BHDP
Software number
75Q9H10B#9H1JMAX2
Bosch part / software
10SW001961
Software / calibration
75Q9H10B / 9H1JMAX2

Technical data

Vehicle
BrandBMW
Car model4er
EngineN55B30
FuelPetrol
Displacement3.0
Power306.0PS / 225.1kW
Control unit
Control unitBosch MEVD17.2.G
ECU makerBosch
Hardware numberDST#MEVD17.2.G-N55-M0-B30-F030-EU6-MSA2-HG_AG-LL-RL-CVO-BHDP
Software number75Q9H10B#9H1JMAX2
File
File typeOriginal flash read
File size2,048.00 KB (2,097,152 bytes)
File key9fa5dd96c01b3bcb
Identification read from the file
ECU nameMEVD17.2.G
Read typeCalibration only (data set)
Bosch part / software10SW001961Offset in the file: 0x18001A
Software / calibration75Q9H10B / 9H1JMAX2Offset in the file: 0x1FFE01
Data set descriptionMEVD17.2.G-N55-M0-B30-F030-EU6-MSA2-HG_AG-LL-RL-CVO-BHDP
Bosch project identifier (EPK)43/1/MEVD/11/MEVD172G_75Q9H10B//75Q9H10B///Offset in the file: 0x1FFB0C

About this file

Typical uses: restoring a control unit to its factory software after a failed flash or a corrupt memory, a clean base before any change, comparing a read of your own with the original. The checksum is the one of the read; your programmer or the CARTESIAN app corrects it after a change.

In CARTESIAN this original file is the base for lambda off, EGR off, flaps off, start/stop off and DTC off, each saved with a correct checksum, and for returning a modified unit to stock.

How to use this file

  1. Order with your e-mail address; the download link comes right after the payment and is valid for 30 days.
  2. Open the file in your programmer, compare its numbers with your unit and check the checksum.
  3. Write it only to a Bosch MEVD17.2.G whose label carries the same hardware and software numbers.

Before you write Compare the numbers on your control unit with this file, hardware number DST#MEVD17.2.G-N55-M0-B30-F030-EU6-MSA2-HG_AG-LL-RL-CVO-BHDP and software number 75Q9H10B#9H1JMAX2. A file written to a unit with other numbers can damage it. Not sure? Search with your own read on the Database page: it is compared by content.

Other pairs of Bosch MEVD17.2.G

Bosch MEVD17.2.G original files

The Bosch MEVD17.2.G unit page