Original file

BMW 6er Bosch MEVD17.2.H #C1#DST#MEVD17.2.H-S63Tue-B44-T1-F010-ULEV2---_DKG-SWT-P-St3 / 10SW005946

An original (stock) flash read of the Bosch MEVD17.2.H control unit, fitted in BMW 6er, hardware number #C1#DST#MEVD17.2.H-S63Tue-B44-T1-F010-ULEV2---_DKG-SWT-P-St3 and software number 10SW005946, 4,096.00 KB. The file is supplied exactly as it was read from the unit, byte for byte; nothing is changed in it.

Is this your file?

Compare these numbers with the label on your control unit before you order.

Vehicle
BMW 6er4.4 petrol 560PS
Control unit
Bosch MEVD17.2.H
Read type
Calibration only (data set)
File
4,096.00 KB · Flash
Hardware number
#C1#DST#MEVD17.2.H-S63Tue-B44-T1-F010-ULEV2---_DKG-SWT-P-St3
Software number
10SW005946
Software / calibration
8BC98BGB

Technical data

Vehicle
BrandBMW
Car model6er
Engine4.4 petrol 560PS
Power560.0PS / 411.9kW
Control unit
Control unitBosch MEVD17.2.H
ECU makerBosch
Hardware number#C1#DST#MEVD17.2.H-S63Tue-B44-T1-F010-ULEV2---_DKG-SWT-P-St3
Software number10SW005946
File
File typeOriginal flash read
File size4,096.00 KB (4,194,304 bytes)
File keya3c2bc75e5fce106
Identification read from the file
ECU nameMEVD17.2.H
Read typeCalibration only (data set)
Bosch part / software10SW005946Offset in the file: 0x18001A
Software / calibration8BC98BGBOffset in the file: 0x1FFE01
Data set descriptionMEVD17.2.H-S63Tue-B44-T1-F010-ULEV2---_DKG-SWT-P-St3
Bosch project identifier (EPK)43/1/MEVD/11/MEVD172H_8BC98BGB//8BC98BGB///Offset in the file: 0x1FFB0C

About this file

Typical uses: restoring a control unit to its factory software after a failed flash or a corrupt memory, a clean base before any change, comparing a read of your own with the original. The checksum is the one of the read; your programmer or the CARTESIAN app corrects it after a change.

In CARTESIAN this original file is the base for lambda off, EGR off, flaps off, start/stop off and DTC off, each saved with a correct checksum, and for returning a modified unit to stock.

How to use this file

  1. Order with your e-mail address; the download link comes right after the payment and is valid for 30 days.
  2. Open the file in your programmer, compare its numbers with your unit and check the checksum.
  3. Write it only to a Bosch MEVD17.2.H whose label carries the same hardware and software numbers.

Before you write Compare the numbers on your control unit with this file, hardware number #C1#DST#MEVD17.2.H-S63Tue-B44-T1-F010-ULEV2---_DKG-SWT-P-St3 and software number 10SW005946. A file written to a unit with other numbers can damage it. Not sure? Search with your own read on the Database page: it is compared by content.

Other pairs of Bosch MEVD17.2.H

Bosch MEVD17.2.H original files

The Bosch MEVD17.2.H unit page