Original file

BMW 3 Serie Bosch MEVD17.2.P DST#MEVD17.2.P-N20-Mo-B20-O0-F030-EU6-HGAG_-LL-RL-ALLRAD / 10SW001851

An original (stock) flash read of the Bosch MEVD17.2.P control unit, fitted in BMW 3 Serie, hardware number DST#MEVD17.2.P-N20-Mo-B20-O0-F030-EU6-HGAG_-LL-RL-ALLRAD and software number 10SW001851, 2,048.00 KB. The file is supplied exactly as it was read from the unit, byte for byte; nothing is changed in it.

Is this your file?

Compare these numbers with the label on your control unit before you order.

Vehicle
BMW 3 Serie2.0 petrol 244PS
Control unit
Bosch MEVD17.2.P
Read type
Calibration only (data set)
File
2,048.00 KB · Flash
Hardware number
DST#MEVD17.2.P-N20-Mo-B20-O0-F030-EU6-HGAG_-LL-RL-ALLRAD
Software number
10SW001851
Software / calibration
9VT9G20B / 9G2LBNX2

Technical data

Vehicle
BrandBMW
Car model3 Serie
Engine2.0 petrol 244PS
Power244.7PS / 180.0kW
Control unit
Control unitBosch MEVD17.2.P
ECU makerBosch
Hardware numberDST#MEVD17.2.P-N20-Mo-B20-O0-F030-EU6-HGAG_-LL-RL-ALLRAD
Software number10SW001851
File
File typeOriginal flash read
File size2,048.00 KB (2,097,152 bytes)
File keya560b6eba78c80f2
Identification read from the file
ECU nameMEVD17.2.9
Read typeCalibration only (data set)
Bosch part / software10SW001851Offset in the file: 0x18001A
Software / calibration9VT9G20B / 9G2LBNX2Offset in the file: 0x1FFE01
Data set descriptionMEVD17.2.P-N20-Mo-B20-O0-F030-EU6-HGAG_-LL-RL-ALLRAD
Bosch project identifier (EPK)43/1/MEVD/11/MEVD1729_9VT9G20B//9VT9G20B///Offset in the file: 0x1FFB0C

About this file

Typical uses: restoring a control unit to its factory software after a failed flash or a corrupt memory, a clean base before any change, comparing a read of your own with the original. The checksum is the one of the read; your programmer or the CARTESIAN app corrects it after a change.

In CARTESIAN this original file is the base for lambda off, EGR off, flaps off, start/stop off and DTC off, each saved with a correct checksum, and for returning a modified unit to stock.

How to use this file

  1. Order with your e-mail address; the download link comes right after the payment and is valid for 30 days.
  2. Open the file in your programmer, compare its numbers with your unit and check the checksum.
  3. Write it only to a Bosch MEVD17.2.P whose label carries the same hardware and software numbers.

Before you write Compare the numbers on your control unit with this file, hardware number DST#MEVD17.2.P-N20-Mo-B20-O0-F030-EU6-HGAG_-LL-RL-ALLRAD and software number 10SW001851. A file written to a unit with other numbers can damage it. Not sure? Search with your own read on the Database page: it is compared by content.

Other pairs of Bosch MEVD17.2.P

Bosch MEVD17.2.P original files

The Bosch MEVD17.2.P unit page