Original file

BMW 3er Bosch MEVD17.2.P DST#MEVD17.2.P-N20-Mo-B20-O0-F030-EU6-HGAG_-LL-RL-ALLRAD / 9VT9G20B#9G2LBNX8

An original (stock) flash read of the Bosch MEVD17.2.P control unit, fitted in BMW 3er, hardware number DST#MEVD17.2.P-N20-Mo-B20-O0-F030-EU6-HGAG_-LL-RL-ALLRAD and software number 9VT9G20B#9G2LBNX8, 4,096.00 KB. The file is supplied exactly as it was read from the unit, byte for byte; nothing is changed in it.

Is this your file?

Compare these numbers with the label on your control unit before you order.

Vehicle
BMW 3erN20B20 · 245.0PS / 180.2kW
Control unit
Bosch MEVD17.2.P
Read type
Full read (boot area included)
File
4,096.00 KB · Flash
Hardware number
DST#MEVD17.2.P-N20-Mo-B20-O0-F030-EU6-HGAG_-LL-RL-ALLRAD
Software number
9VT9G20B#9G2LBNX8
Bosch part / software
10SW001851
Software / calibration
9VT9G20B / 9G2LBNX8

Technical data

Vehicle
BrandBMW
Car model3er
EngineN20B20
FuelPetrol
Displacement2.0
Power245.0PS / 180.2kW
Control unit
Control unitBosch MEVD17.2.P
ECU makerBosch
Hardware numberDST#MEVD17.2.P-N20-Mo-B20-O0-F030-EU6-HGAG_-LL-RL-ALLRAD
Software number9VT9G20B#9G2LBNX8
File
File typeOriginal flash read
File size4,096.00 KB (4,194,304 bytes)
File key2694966b017d2ed1
Identification read from the file
ECU nameMEVD17.2.9
Read typeFull read (boot area included)
Bosch part / software10SW001851Offset in the file: 0x18001A
Software / calibration9VT9G20B / 9G2LBNX8Offset in the file: 0x1FFE01
Data set descriptionMEVD17.2.P-N20-Mo-B20-O0-F030-EU6-HGAG_-LL-RL-ALLRAD
Bosch project identifier (EPK)43/1/MEVD/11/MEVD1729_9VT9G20B//9VT9G20B///Offset in the file: 0x1FFB0C

About this file

Typical uses: restoring a control unit to its factory software after a failed flash or a corrupt memory, a clean base before any change, comparing a read of your own with the original. The checksum is the one of the read; your programmer or the CARTESIAN app corrects it after a change.

In CARTESIAN this original file is the base for lambda off, EGR off, flaps off, start/stop off and DTC off, each saved with a correct checksum, and for returning a modified unit to stock.

How to use this file

  1. Order with your e-mail address; the download link comes right after the payment and is valid for 30 days.
  2. Open the file in your programmer, compare its numbers with your unit and check the checksum.
  3. Write it only to a Bosch MEVD17.2.P whose label carries the same hardware and software numbers.

Before you write Compare the numbers on your control unit with this file, hardware number DST#MEVD17.2.P-N20-Mo-B20-O0-F030-EU6-HGAG_-LL-RL-ALLRAD and software number 9VT9G20B#9G2LBNX8. A file written to a unit with other numbers can damage it. Not sure? Search with your own read on the Database page: it is compared by content.

Other pairs of Bosch MEVD17.2.P

Bosch MEVD17.2.P original files

The Bosch MEVD17.2.P unit page